Oshkosh Corporation JERR-DAN HDR 70/85-530 страница 99 Скачать руководство пользователя

Страница: 99 / 106

5-376-000094
REV. 3 - 03/10

Section IV: Glossary

Page 91

Forks

- A device attached to the lift bar for lifting a vehicle by the tires, axle, frame,

or structural member. May be classified as chain, axle, or frame forks.

FW (Frame Width)

- The overall width of the chassis frame measured outside to

outside behind the cab.

GAWR (Gross Axle Weight Rating)

- The value specified by the manufacturer as

the load-carrying capacity of a single-axle system as measured at the
tire-roadway interface.

GCWR (Gross Combination Weight Rating)

- Represents the entire weight of a

vehicle on the ground with a trailer or trailers including vehicle, equipment,
driver, fuel, and payload (everything that moves with the vehicle.) Gross
combination weights published represent maximum allowed.

Grab Hook

- For use with chains and some tow-sling hookups.

Grid

- A device that attaches to the lift bar for engaging the tires of a towed vehicle.

GVWR (Gross Vehicle Weight Rating)

- The maximum total vehicle rated capacity,

measured at the tire ground interface, as rated by the chassis manufacturer.

GVW (Gross Vehicle Weight)

- Value specified by the manufacturer as the

maximum loaded weight of a single vehicle including all equipment, fuel,
body, payload, driver, etc.

Headboard -

Structure on which an emergency light bar is mounted.

Hook-up Chains

- Length of chain used to connect a recovery vehicle to a casualty

vehicle.

Horizontal Center of Gravity (HCG)

- The point at which half of the gross weight

is forward and half is aft.

Hydraulic Control Valve

- A mechanical device to divert or control the flow of fluid

in a hydraulic system.

Hydraulic Hose

- Flexible oil lines used to transmit fluid.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды