Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя

Страница: 50 / 106

5-376-000094

REV. 3 - 03/10

Section II: Operation

Page 42

13. If the remote hand controller was

used, turn the CONTROL switch
“OFF”. (Switch is located on
panel on the floor.)

WARNING:

Never fold the boom up into the
storage position without
removing the towing adapters
from the crossbar receivers.

CHAIN FORKS (OPTIONAL)

1. Insert the chain forks into the

receivers on the crossbar.

2. Extend the under lift boom up to

the casualty vehicle so that the
chain forks are in the proper
position for lifting.

3. Attach the hook-up chains to the

casualty vehicle. Hook the
chains through the chain forks
and secure any extra chain to
the hooks on the lift receivers.
The use of wood blocks and
rubber mats may be required to
protect the casualty vehicle.

4. Raise the boom to lift the

casualty vehicle slightly. At the
same time make sure that you
are not going to damage any
components.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды