Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя | Manualshive

Страница: 19 / 106

background image

5-376-000094
REV. 3 - 03/10

Section I: Safety

Page 11

NOTE

These ratings apply to the structural design of the HDR70/85 - 565 only . They
might be limited by the axle rating and gross vehicle weight rating of the truck
chassis.

The payload and towing capacity of any towing vehicle must meet the
following:
• The actual payload on the towing vehicle must not exceed the posted

rating and the towed vehicle load must not exceed the posted lift /
towing ratings.

• The total weight of the towing vehicle (cab chassis, body, payload, driver,
passenger(s), tools, fuel, etc.) and the towed vehicle load must not

exceed the GVWR (Gross Vehicle Weight Rating) of the towing vehicle.

• The total weight of the towing vehicle and a towed vehicle load must be

distributed so that each axle’s GAWR (Gross Axle Weight Rating) is not
exceeded.

• The total weight of the towing vehicle and towed vehicle (everything

that moves with the towing vehicle) must not exceed the GCWR
(Gross Combination Weight Rating) of the towing vehicle.

Staying within these ratings is necessary to maintain the safety and
performance of the towing vehicle.

CHECK TRUCK MANUAL FOR SPECIFIC GVW & AXLE RATINGS. ALSO LOOK
AT THE CERTIFICATION DECAL AFFIXED TO DRIVER’S SIDE DOOR JAMB, HINGE
PILLAR OR LATCH POST AND THE STRUCTURAL CAPACITIES PLACARD ON
THE UNIT.

Ea

st

ern

W

re

cke

r Sa

le

s

In

c

«
...
17
18
19
20
21
...
»

Содержание JERR-DAN HDR 70/85-530











































































































Отзывы:

Нет отзывов

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FASTERHOLT Страницы: 96

Бренд: Garmin Страницы: 10

Бренд: Naviom Страницы: 31

Бренд: Xiitech Страницы: 6

Бренд: Maeda Страницы: 276

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренд: Olympus Страницы: 130

Бренд: GE Страницы: 37

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: Martin Страницы: 202

ABS-Lock III-BE

Бренд: ABS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды