Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя

Страница: 42 / 106

5-376-000094

REV. 3 - 03/10

Section II: Operation

Page 34

5. Adjust the electronic or manual throttle control to elevate the engine

speed to approximately 1000-1200 R.P.M. of P.T.O. output shaft speed
for optimum performance.

CAUTION:

Never exceed 1200 R.P.M. When your hook up is complete, reset
the engine idle to normal.

6. Confirm the recovery vehicle’s position in relation to the casualty vehicle

to be towed. Nine (9) ft. is recommended. Reposition the recovery vehicle
if necessary.

Be sure the casualty vehicle is not in gear or park.

Keep the brake set.

7. Using the tilt fuction, unfold the

under lift boom down until it is in
the horizontal position.

8. Lower the under lift boom to

about one (1) in. from the ground
and swing the crossbar parallel
to the casualty vehicle.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды