Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя страница 95

Страница: 95 / 106

5-376-000094
REV. 3 - 03/10

Section IV: Glossary

Page 87

Anchoring Device

- Used to attach cable ends, snatch blocks, safety chains,

and tie-down assemblies to the towing vehicle.

Approach Angle

- Angle between the plane of the platform and the ground.

Attachment

- Any device that can be added to a basic unit or assembly.

Auxiliary Braking Device

- A device which attaches to the disabled vehicle to

assist the tow truck's brakes in retarding or stopping both vehicles.

Auxiliary Equipment

- Equipment that is not necessary to perform the basic

function of the primary equipment.

Auxiliary Towing Lights

- Stop, tail, and turn signal lights attached to the trailing

end of the towed vehicle and operated as part of the towing vehicle lighting
system.

Bending Moment

- The force times the distance from a reference point to the

point the force is applied causing bending.

Bird Nesting

- The tangling and intertwining of wraps and layers on a drum.

Body

- The structure mounted on a chassis cab or that portion of the vehicle that

carries the load.

Body Hinge

- The attachment mechanism connecting the body to the hinge pin

at the pivot axis about which the body rotates into the tilt position.

Body Subframe

- Another term for body understructure or mounting frame.

Body Weight

- Unmounted weight of a body with applicable options.

Boom

- The structure member that supports the load.

Boom Angle

- The boom angle is measured between a horizontal line and a line

through the boom pivot and center of sheave.

Boom Head

- The structural member at one end of the boom which can swivel

and support the load lifted through the sheave and sheave support device.

GLOSSARY OF TERMS

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Бренды по названию

Популярные бренды