Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя

Страница: 96 / 106

5-376-000094

REV. 3 - 03/10

Section IV: Glossary

Page 88

Boom Length

- The straight line distance from center of the revolving base to the

center of the boom head.

Brakes - Parking

- A system used to hold a stopped machine in a stationary

position.

Brakes - Service

- A primary brake system used for retarding and stopping the

truck.

Bumper - DOT

- A bumper designed to provide rear-end protection that meets

the requirements of FMCSR 393.86.

Bus Bar Grid

- A device used for towing vehicles by lifting one end of the towed

vehicle by the wheels.

CA (Cab to Axle)

- The distance from the back of the truck cab to the center of the

rear axle.

CG (Center of Gravity)

- The point at which the weight of the chassis, body/

equipment and payload, if collectively or individually supported, would
balance vertically, horizontally, and laterally.

CT (Cab to Tandem)

- The distance from the back of the truck cab to a point

midway between the tandem axles.

Cable

- Steel wire rope used for pulling.

Car Carrier

- Vehicles equipped to transport other vehicles mounted on a flat

platform and/or with an additional assembly attached to the rear to facilitate
towing a second vehicle. These units are also known as slidebacks,
rollbacks, transporting equipment carriers and flatbeds. See Carrier.

Carrier

- A platform body with a winch for loading.

Casualty Vehicle

- The damaged or disabled vehicle.

Capacity

- The load that a machine can lift at any given point.

CAUTION

- A signal word used when a potentially hazardous situation exists that

might result in minor injury or property damage.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды