Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя страница 105

Страница: 105 / 106

5-376-000094
REV. 3 - 03/10

Section IV: Glossary

Page 97

Towing

- See Tow.

Tow Bar

- A device for positioning a towed vehicle behind a towing vehicle.

Tow Chain

- Length of chain used to connect the sling with the towed vehicle.

Tow Sling

- A device used for lifting and towing vehicles with a partial load

supported on rubber straps.

Tow Vehicle

- Vehicle used to lift-tow other vehicles.

Towing Light/Bar

- See Auxiliary Towing Lights.

Trailer 5th Wheel Plate

- A plate attached to a tow truck-lifting device that captivates

the kingpin on trailers allowing a trailer to be towed in the same manner as
intended by the trailer manufacturer.

Underlift

- A device used for towing vehicles by lifting one end of the towed

vehicle from under the axle or structural member.

Unloaded Vehicle Weight

- The weight of a vehicle with maximum capacity of all

fluids necessary for operation of the vehicle, but without cargo or occupants.
Also referred to as curb weight.

Valve

- A device which controls fluid flow direction, pressure, or flow rate.

VIN (Vehicle Identification Number)

- The number assigned to a vehicle by the

manufacturer primarily for registration purposes. It may consist of numerals,
letters, or a combination thereof.

WARNING

- A signal word used when a potentially hazardous situation exists

and could result in death or serious injury.

Weight Distribution

- The portion of total weight of the vehicle on each axle.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Бренды по названию

Популярные бренды