Oshkosh Corporation JERR-DAN HDR 70/85-530 страница 24 Скачать руководство пользователя

Страница: 24 / 106

5-376-000094

REV. 3 - 03/10

Section I: Safety

Page 16

• Keep the underlift boom raised high enough

off of the ground when roading to avoid
dragging it over road surfaces.

• Don’t tow a vehicle on its drive wheels unless

steps  have  been  taken  to  protect  its
transmission  and  differential.    Follow  the
recommendations  of  the  vehicle  manu-
facturer.    As  an  alternative,  use  a  towing
dolly.

• Never exceed the front and/or rear axle

ratings of your towing equipment.

• Never extend or retract an outrigger unless it

is in full view from it's operating controls.

• Vehicle must be located on a firm level

surface that will provide support for the
outrigger loading. Use caution when sitting
up near overhanging banks or excavations.

• Don’t use outrigger spades on paved

surfaces unless you are willing to accept
responsibility for damage to such surfaces.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды