Oshkosh Corporation JERR-DAN HDR 70/85-530 страница 30 Скачать руководство пользователя

Страница: 30 / 106

5-376-000094

REV. 3 - 03/10

Section I: Safety

Page 22

• Lubricate and maintain both the wire rope

and  winch  on  regular  intervals.  (See
maintenance charts.)  Inspect the wire rope
for damage.  Damaged, deformed or frayed
wire rope should be replaced before use.

• Don’t continue to wind in wire rope after the

hook is against the boom end.

• All boom placement functions should be

made with the winch wire ropes set in “free
spool” to avoid over tensioning or breaking
the winch wire ropes.

• Avoid using the boom raise or boom up

control to lift a load. This causes undue
stress and weight loading on the rear axle.
Use the winch to lift the load.

• Caution should be taken when retracting

or extending the boom extension while
under load.

• After rigging wire ropes, don’t begin pulling

without rechecking connections.  Make sure
that  all  wire  ropes  and  snatch  blocks  are
securely  attached  and  cannot  accidently
pull loose.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды