Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя страница 31

Страница: 31 / 106

5-376-000094
REV. 3 - 03/10

Section I: Safety

Page 23

• Don’t expect your wrecker to tow loads equal

to the wrecker ratings. Wrecker ratings apply
to loads imposed during recovery with the
wrecker properly stabilized.

• Do not raise, lower, or move the boom near

power lines. Hazardous voltage will cause
severe injury or death.

• To avoid birdnesting and premature failure of

the wire rope, always keep tension on the wire
rope when winding or unwinding.

• Don’t exceed ratings of booms, wire ropes,

snatch  blocks,  or  winches.    Stay  within
nameplate ratings.  Note that boom ratings
decrease  significantly  as  the  boom  is
extended.

• Don’t drive with the wrecker boom

extended.

• When making a pull to the side, always apply

an equal load in the opposite direction of the
pull to stabilize the wrecker.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Бренды по названию

Популярные бренды