Oshkosh Corporation JERR-DAN HDR 70/85-530 Скачать руководство пользователя

Страница: 106 / 106

5-376-000094

REV. 3 - 03/10

Section IV: Glossary

Page 98

Wheel Arm

- A device that attaches to the lift bar for engaging the tires of a towed

vehicle.

Wheelbase

- Horizontal dimension from centerline of front axle to the effective

centerline of the rear axle(s).

Wheel Chock -

A device used to prevent chassis movement.

Wheel Fork

- See Wheel Arm.

Wheel-Lift

- A device used for towing vehicles by lifting one end of the towed

vehicle by the wheels.

Wheel Securing Device

- A strap or mechanical device, when attached to the lift-

bar, which limits the potential for separation of the towed vehicle from the
underlift, during operating conditions.

Wheel Straps

- Used to tie down wheels of the towed vehicle when using wheel-

lift, car carrier, or dolly towing equipment to limit the potential for separation
of the towed vehicle from the towing apparatus.

Winch

- A device for winding and unwinding cable.

Wire Rope

- See Cable

Working Load Limit

- Minimum breaking strength divided by the factor of safety.

Wrap

- A single coil of wire rope wound on a drum.

Wrecker

- See Tow Vehicle, or Recovery Vehicle.

ern

cke

r Sa

Содержание JERR-DAN HDR 70/85-530











































































































Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды

Oshkosh Corporation JERR-DAN HDR 70/85-530, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание JERR-DAN HDR 70/85-530

Отзывы:

Похожие инструкции для JERR-DAN HDR 70/85-530

Бренды по названию

Популярные бренды