Oracle Acme Packet 3900 Скачать руководство пользователя | Manualshive

Страница: 9 / 70

background image

1

Safety

This chapter provides an overview of the recommended safety precautions for
installing the Acme Packet 3900 System.

Before you install your Acme Packet 3900 System, Oracle recommends that you
review the contents of this chapter and the Installation chapter. Both chapters
provide information intended to protect you and your Acme Packet 3900 System from
experiencing any harm during the installation process. These chapters also provide
information that helps to keep your Acme Packet 3900 System functioning properly
and prevent damage.

Environmental, Safety, and Regulatory Certifications

For information regarding safety and regulatory certifications applicable to the Acme
Packet 3900, refer to the Acme Packet Platforms Safety and Compliance Guide.

General Safety Precautions

To ensure general safety, follow the safety precautions listed in this section.

Fan Module

To avoid overheating the system, do not block the air inlets or the fan module, or
otherwise obstruct airflow to the system. Keep the area around the Acme Packet 3900
System clean and clutter-free.

Unit Maintenance

Aside from the fan module, power supply, air filter, transcode module, and TDM
module, there are no user-serviceable parts inside the Acme Packet 3900 System
chassis. Only professionals trained to maintain, adjust, or repair the Acme Packet
3900 System may provide these services.

Fiber Optic Cable

Looking into a fiber optic cable can cause eye damage. Never look directly into the
end of the fiber optic cables. Instead, use a fiber optic power meter to determine if
power is present.

Environmental Specifications

Adhere to the stated environmental specifications for the Acme Packet 3900.

1-1

«
...
7
8
9
10
11
...
»

Содержание Acme Packet 3900







































































Отзывы:

Нет отзывов

Похожие инструкции для Acme Packet 3900

i-bus KNX IPR/S 3.5.1

Бренд: ABB Страницы: 44

Бренд: National Instruments Страницы: 17

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: CSS Страницы: 2

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Ethernet Communication Module DVPEN01-SL

Бренд: Delta Electronics Страницы: 54

Бренд: H3C Страницы: 3

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

Бренд: A2B Electronics Страницы: 24

Бренд: ZALMAN Страницы: 6

Бренд: QNAP Страницы: 54

Бренд: Paradyne Страницы: 6

Бренд: SeaLevel Страницы: 34

OptiBond 210 C Series

Бренд: i-MO Страницы: 16

Бренд: LevelOne Страницы: 3

Бренд: VideoWave Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды