manualshive.com logo in svg

Oracle Acme Packet 3900, Руководство по установке и обслуживанию оборудования, Страница: 51 / 70

Поделиться
Скачать
Oracle Acme Packet 3900 Скачать руководство пользователя страница 51

Note:

You can perform routine maintenance on the Acme Packet 3900 front panel
fans and air filter with the unit normally installed in the equipment rack. Also,
you do not need to remove the the power from the chassis.

Clean the Air Inlets

1.

Remove the bezel from the chassis by gripping the two left corners and pulling on
it. The bezel is held on magnetically.

2.

Remove the air filter.

3.

Clean the bezel by gently wiping it with a clean, dry cloth or by blowing
compressed air through it.

4.

Install a clean air filter on the bezel.

5.

Attach the bezel to the unit by hooking the bezel's right side into its slots and
pivoting until the magnet catches the chassis.

Replace a Fan

To maintain unit operations, you must be able to remove the malfunctioning fan and
quickly replace it with a functioning one to prevent the unit from overheating. To obtain
a replacement fan, contact Oracle customer support.

Chapter 5

Maintenance With Power

5-7

Содержание Acme Packet 3900







































































Отзывы:

Нет отзывов