Oracle Acme Packet 3900 Скачать руководство пользователя

Страница: 35 / 70

Note:

Use a 10 Amp fused circuit for each AC power supply.

Note:

This equipment is intended for installation in locations where National
Electrical Code (NEC) applies.

To install the AC power cords in the Acme Packet 3900:

Locate the two AC power cords shipped with your Acme Packet 3900. Choose one
power supply to work on first.

Connect one power cord to the power supply by inserting the 3-lead IEC-60320
plug into the IEC connector located on the power supply.

Connect the other power cord to the power supply by inserting the 3-lead
IEC-60320 C13 plug into the IEC-60320 C14 IEC connector located on the power
supply.

Route the AC power cords through your rack and cabling system to the power
outlets.

Plug the supply end of each power cord into its own circuit.

Note:

To remove AC power cables from the Acme Packet 3900, reverse the
previous steps in this procedure.

--OR--

Set the System Power switch to the On position to provide power to the Acme
Packet 3900. The Acme Packet 3900 will start to boot.

DC Power Cord Installation

This section explains you how to install a DC power cord.

Important:

This equipment is intended for installation in Network Telecommunication
Facilities.

Caution:

Use a 30 Amp fused circuit for each DC power supply.

Chapter 3

Ground and Power Cable Installation

3-14

Содержание Acme Packet 3900







































































Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды

Oracle Acme Packet 3900, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды