Oracle Acme Packet 3900 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 70

Oracle Acme Packet 3900 Скачать руководство пользователя страница 13

Once the slide rails are installed on the chassis and on the equipment rack, the
chassis can be installed in the rack by inserting the chassis slide rails into the tracks of
the slide rails already mounted on the equipment rack. When the locking latch on the
chassis slide rail meets the hole in the rack slide rail, the rails lock together. Push the
locking latch in to continue to slide the chassis into the rack rails.

Once the chassis has been fully inserted into the rack, turning the captive
thumbscrews clockwise will lock the chassis securely into the rack.

System Processor

Processor

The Acme Packet 3900 processor is located on the main board. This processor
handles the management and signal processing within the unit as well as performing
call and media control.

Control Panels

This section describes the front and rear control panels of the Acme Packet 3900.

Front Panel

The Acme Packet 3900 front control panel provides easy access to several unit
components. You can access the power pushbutton and view the power LED, the
alarm LED, and the high availability LEDs. The following is a close up of the front
control panel.

Chapter 2

System Processor

2-2

«
...
11
12
13
14
15
...
»

Содержание Acme Packet 3900







































































Отзывы:

Нет отзывов