Oracle Acme Packet 3900 Скачать руководство пользователя

Страница: 22 / 70

Installation

This chapter provides information about how to install the Acme Packet 3900 and its
associated components.

Shipped Parts

Each Acme Packet 3900 ships in one box. Inside this box is the Acme Packet 3900
chassis and the accessory kit. The ordered modules are already installed in the
chassis.

Table 3-1 Shipping Contents

Location

Item

Main Shipping Box

Acme Packet chassis

Accessory Kit

•

Console adapter

•

AC or DC power cords, one per power
supply

•

Grounding cable

•

Slide Rail Mounting Kit

Installation Tools and Parts

The following tools and parts are required to install the Acme Packet 3900 into your
equipment rack:

•

#2 Phillips-head screwdriver

•

Small flat-head screwdriver

•

Rack and associated mounting hardware

•

Shielded Ethernet CAT5e or CAT6 RJ45 cables

•

11/32” nut driver

•

5/16" nut driver

Recommended Tools and Parts

Oracle recommends that you have the following parts on hand:

•

Cable labels

•

UPS for AC installations

•

ESD wrist or heel straps

•

ESD-safe location

3-1

Содержание Acme Packet 3900







































































Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды

Oracle Acme Packet 3900, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды