Oracle Acme Packet 3900 Скачать руководство пользователя страница 69

Страница: 69 / 70

Specification

Description

Temperature

The Acme Packet 3900 is required to operate
within the temperature range of:

0° C to +40° C, 32° F to 104° F (operating)

-20° C to +65° C, -4° F to 149° F (storage)

Relative Humidity

Operating conditions of 10% to 85% humidity
under non-condensing operating conditions

Maximum Altitude

The Acme Packet 3900 is required to operate
below the maximum altitude of 10,000 feet.

Air Flow

40 CFM front to back

Power Dissipation

160W typical 220W maximum

Connector Specifications

Refer to the following table for information about the connector specifications.

Specification

Description

AC Connector Port

The IEC lead connector port on each power
supply accepts a 3-lead IEC-60320 C14
connector for AC power installations (2).

RJ45/Management Ethernet Ports

The 3 x 8-pin RJ45 10/100/1000BaseT ports
are compliant with IEEE's 802.3, 802.3u, and
802.3ab.

RS232/Serial Port

The RS232 serial port uses an 8-pin RJ45
connector that supports RS232 protocol.

1 GbE Media Ports

The four 1GbE fiber optic connection ports
(P0-P3) are implemented as SFP sockets.
Duplex LC or copper SFPs may be used.

Terminal Block Connections

The terminal block connections accept a bare
(tinned) wire for DC power installations on
each DC power supply (2).

DC Input Connector

The Input connector on each DC power supply
is a 2-circuit plug.

RJ48C T1/E1 Ports (Optional)

Mechanical Arrangement: 4 Miniature 8-
position jacks.
Usage: 1.544 Mbps digital services.

Electrical Network Connection: T&R, T1 R1,
conductors 7 and 8provide cable shield
integrity.

Optical Transceiver Interface Module Specification

Refer to the following table for information about the optical specifications of the optical
transceivers.

Specification

Single Mode (SX) Fiber
Module

Multi Mode (LX) Fiber
Module

Wavelength

1310 nm

850 nm

Laser Type

VCSEL

Chapter 6

Connector Specifications

6-3

Содержание Acme Packet 3900







































































Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Oracle Acme Packet 3900, Руководство по установке и обслуживанию оборудования, Страница: 69 / 70

Результаты поиска

Содержание Acme Packet 3900

Отзывы: