Oracle Acme Packet 3900 Скачать руководство пользователя

Страница: 67 / 70

Specifications

This chapter provides information regarding the physical, electrical, environmental,
and connector specifications of the Acme Packet 3900.

Environmental, Safety, and Regulatory Certifications

For information regarding safety and regulatory certifications applicable to the Acme
Packet 3900, refer to the Acme Packet Platforms Safety and Compliance Guide.

Physical Specifications

System Chassis Specifications

This table lists the physical dimensions and weight of the Acme Packet 3900 chassis.

Specification

Description

Height

1.72” (4.37 cm) (1U)

Width

17.10” (43.43 cm) (+ mounting ear width: 19”
(48.26 cm))

Depth

15.75” (40.10 cm) (+ mounting slide bar depth)

Weight

approximately 14.2 lbs (6.44 kg), fully loaded

AC Power Supply Physical Dimensions

This table lists the physical dimensions and weight of the Acme Packet 3900 AC
power supply.

Specification

Description

Height

1.58” (4.01 cm)

Width

3.402” (8.64 cm)

Depth

9.33” (23.70 cm)

Weight

2.34 lbs. (1.06 kg)

Note:

This equipment is intended for installation in locations where National
Electrical Code (NEC) applies.

6-1

Содержание Acme Packet 3900







































































Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды

Oracle Acme Packet 3900, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды