Oracle Acme Packet 3900 Скачать руководство пользователя

Страница: 68 / 70

DC Power Supply Physical Dimensions

This table lists the physical dimensions and weight of the Acme Packet 3900 DC
power supply.

Specification

Description

Height

1.58” (4.01 cm)

Width

3.4” (8.63 cm)

Depth

9.33” (23.70 cm)

Weight

2.34 lbs. (1.06 kg)

Note:

This equipment is intended for installation in Network Telecommunication
Facilities.

Fan Module Specifications

This table lists the fan module specifications for the Acme Packet 3900.

Specification

Description

Number of Fans

Total Maximum Airflow

40 CFM

Electrical Specifications

Refer to the following tables for information regarding the electrical specifications.

Power Supply Input Circuit Fuse Requirements

This table lists the input circuit fuse and cable size requirements.

Power Circuit

Fuse Rating

Power Cable Size

120 VAC

15 AMP

18 AWG

240 VAC

7.5 AMP

18 AWG

-48 VDC

10 AMP

10 AWG

Environmental Specifications

Oracle recommends that you follow the environmental guidelines in the following table.

Chapter 6

Electrical Specifications

6-2

Содержание Acme Packet 3900







































































Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды

Oracle Acme Packet 3900, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Acme Packet 3900

Отзывы:

Похожие инструкции для Acme Packet 3900

Бренды по названию

Популярные бренды