Onicon F-1100 Series страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 53

background image

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 7

SECTION 2.0: UNPACKING

Turbine flow meters are generally shipped in one package unless optional hardware or equipment is
ordered. This package may contain up to two complete meters along with the optional installation kits.
Any display equipment ordered with the meters, will be packed separately. Please open all packages
with caution to avoid damaging to their contents. In the event that anything is damaged when you
receive it, notify the shipping company immediately and the ONICON customer service department.
Most products are shipped insured unless the customer specifically requests otherwise.

2.1 CHECKING THAT YOU HAVE RECEIVED EVERYTHING

The Documentation

Enclosed with each flow meter is a comprehensive documentation package which
includes the following items:

• Installation and Operation Guide
• Flow Meter Calibration Certificate

Please notify the ONICON customer service department if any documents are missing.

The Flow Meter

The flow meter was carefully packed prior to shipment and should arrive without any
damage. Prior to installation, inspect for physical damage such as broken turbine blades or
a damaged stem.

• Test the turbine(s) to see that they rotate freely when you gently blow on them

parallel to their shafts.

• Make sure that the threads on the insertion meter hot tap adapter have not been

damaged.

• Inspect the insertion meter stem for bends or other damage. The stem forms

the seal against liquid leakage as it slides through an ‘O’ ring inside the hot tap
adapter. Deep scratches may cause leakage.

• The serial and model numbers on the laminated wiring connection /calibration

data tag attached to the meter should match the numbers on the tag mounted
directly on the flow meter. Be sure that the unit was calibrated to the correct pipe
size and flow range.

«
...
5
6
7
8
9
...
»

Содержание F-1100 Series






















































Отзывы:

Нет отзывов

Похожие инструкции для F-1100 Series

Бренд: Keithley Страницы: 148

Бренд: OHAUS Страницы: 26

Бренд: La Crosse Technology Страницы: 8

Бренд: A&D Страницы: 24

Бренд: Apera Страницы: 2

Бренд: Erma Electronic Страницы: 24

Бренд: Apera Instruments Страницы: 32

Бренд: In-situ Страницы: 50

Бренд: UNI-T Страницы: 11

Бренд: wtw Страницы: 52

Бренд: PASCO Страницы: 2

Бренд: Topcon Страницы: 80

SONICHEK PRO 3550

Бренд: Triplett Страницы: 2

Бренд: Extech Instruments Страницы: 8

Бренд: Klein Tools Страницы: 6

Бренд: ROM Elektronik Страницы: 14

Бренд: Tonghui Страницы: 120

Бренд: Sperry instruments Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды