Onicon F-1100 Series Скачать руководство пользователя | Manualshive

Страница: 19 / 53

background image

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 19

3.6 INLINE METER STRAIGHT RUN REQUIREMENTS AND MECHANICAL INSTALLATION

Locating the meter

1. Install process connections (sweat or threaded end pieces) making certain to leave adequate

straight unobstructed pipe runs upstream and downstream of the meter location.

a. The minimum upstream straight run should be at least 20 diameters and the downstream
straight run should be at least 5 diameters in length.
b. If more than 25 diameters of straight run are available at the installation site the excess
straight run should be upstream of the meter location.
c. Please note that ONICON strongly recommends the use of strainers upstream of the meter
location.
d. ONICON also recommends the installation of isolation valves and a bypass loop to
accommodate servicing the meter.

Isolation Valve

Normally Open

5 Dia. Minimum

Straight Run

Downstream

Isolation Valve

Normally Open

Bypass Valve

Normally Closed

20 Dia. Minimum

Straight Run

Upstream

y-Strainer

Upstream of

Flow Meter

I

nstalling the meter body

1. Make sure the unions are free of nicks or scratches on either end of the flow
meter body and on the process connections.
2. Spray the union faces with a silicone spray or apply a thin coat of beeswax to enhance
seating. Do not use paste thread sealant on union faces.
3. Recommended torques for union seal: 70 ft/lbs minimum
4. Make sure alignment of pipe does not put lateral stress on either joint.

TYPICAL INLINE METER INSTALLATION

Process

Connection

Process

Connection

Unions

«
...
17
18
19
20
21
...
»

Содержание F-1100 Series






















































Отзывы:

Нет отзывов

Похожие инструкции для F-1100 Series

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Бренд: Magnum Energy Страницы: 3

Kotron 805 series

Бренд: Magnetrol Страницы: 36

Бренд: Magnescale Страницы: 104

Бренд: Magnescale Страницы: 44

Бренд: Keithley Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды