Onicon F-1100 Series страница 2 Скачать руководство пользователя

Страница: 2 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 2

SAFETY INFORMATION

This meter was calibrated at the factory before shipment. To ensure correct use of the meter, please read
this manual thoroughly.

Regarding this manual:

•

This manual should be passed on to the end user.

•

Before use, read this manual thoroughly to comprehend its contents.

•

The contents of this manual may be changed without prior notice.

•

ONICON’s written permission.

•

ONICON makes no warranty of any kind with regard to this material, including, but not

limited to, implied warranties of merchantability and suitability for a particular purpose.

•

All reasonable effort has been made to ensure the accuracy of the contents of this manual.

However, if any errors are found, please inform ONICON.

•

ONICON assumes no responsibilities for this product except as stated in the warranty.

•

If the customer or any third party is harmed by the use of this product, ONICON assumes

no responsibility for any such harm owing to any defects in the product which were not

predictable, or for any indirect damages.

Safety Precautions:

The following general safety precautions must be observed during all phases of installation,

operation, service, and repair of this product. Failure to comply with these precautions or with

specific WARNINGS given elsewhere in this manual violates safety standards of design,

manufacture, and intended use of the product. ONICON Incorporated assumes no liability for the

customer’s failure to comply with these requirements. If this product is used in a manner not

specified in this manual, the protection provided by this product may be impaired.

The following symbols are used in this manual:

WARNING

Messages identified as “WARNING” contain information regarding the personal safety of

individuals involved in the installation, operation or service of this product.

CAUTION

Messages identified as “CAUTION” contain information regarding potential damage to the

product or other ancillary products.

IMPORTANT NOTE

Messages identified as “IMPORTANT NOTE” contain information critical to the proper

operation of the product.

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды