Onicon F-1100 Series Скачать руководство пользователя

Страница: 3 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 3

TABLE OF CONTENTS

1.0 INTRODUCTION

.............................................................................................................4

1.1

Purpose of This Guide ..........................................................................................4

1.2

Typical Turbine Flow Meters ...............................................................................4

1.3

Standard Features and Specifications ..................................................................5

1.4

Model Numbering System ....................................................................................6

1.5

Additional Required Hardware ............................................................................6

1.6

Warranty and Serial Number ................................................................................6

2.0 UNPACKING

................................................................................................................7

2.1

Checking That You Have Received Everything ...................................................7

3.0

INSTALLATION, REMOVAL & ADJUSTMENT

.............................................................8

3.1

Site Selection ........................................................................................................8

3.2

Insertion Meter Straight Run Requirements ......................................................10

3.3

Insertion Meter Mechanical Installation ............................................................12

3.3.1 Insertion Meter Installation Kits ...............................................................13

3.3.2 ONICON Standard Installation Hardware Kits .........................................13

3.3.3 ONICON Hot Tap Installation Hardware Kits ...........................................13

3.3.4 Customer Supplied Installation Hardware ...............................................14

3.3.5 Confirming the Stack Height .....................................................................15

3.4

Installing the Insertion Meter .............................................................................16

3.4.1 Adjusting of the Meter Insertion Depth ....................................................17

3.5

Removal of the Insertion Meter ..........................................................................17

3.6

Inline Flow Meter Straight Run Requirements and Mechanical Installation...19

3.7

Wiring Connections ............................................................................................20

4.0

START-UP & COMMISSIONING

...................................................................................21

4.1

Helpful Hints for Start-up and Commissioning ................................................21

4.2

Insertion Meter Start-up and Commissioning ...................................................22

4.3

Insertion Meter Start-up and Commissioning Worksheet .................................23

4.4

Inline Meter Start-up and Commissioning ........................................................24

4.5

Inline Meter Start-up and Commissioning Worksheet ......................................25

4.6

Troubleshooting Guide .......................................................................................26

5.0

ANALOG ADJUSTMENT PROCEDURE

.......................................................................27

5.1

General Discussion .............................................................................................27

5.2

Analog Adjustment Procedure ...........................................................................27

5.2.1 Equipment Required ..................................................................................27

5.2.2

Procedure ...................................................................................................28

APPENDIX

User Connections and Internal Wiring Diagrams

Installation Hardware Instructions

Insertion Turbine Assembly Detail Drawings

Conditions of Sale

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды