Onicon F-1100 Series Скачать руководство пользователя

Страница: 46 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 46

05-11

0542-2/15953

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699

www.onicon.com • [email protected]

For Use With Kits: INSTL19, INSTL20, INSTL21, INSTL22, INSTL23, INSTL24,

INSTL25, INSTL26, INSTL27, INSTL28, INSTL29, INSTL30, INSTL75

Pipe saddle types vary by application.

Important Note

ONICON provides pipe saddles to facilitate the installation of our flow meters. These saddles

are purchased from leading manufacturers who provide quality products. Separate installation

instructions accompany the saddle. Please follow these instructions when installing the

saddle. Pay particular attention to bolt torque specifications and temperature/pressure limits.

Installation Hardware Instructions
Hot Tap Installation Kit for Applications Requiring Pipe Saddles

For F-1100, F-1200 & FB-1200 Series Insertion Turbine Flow Meters

This kit can be installed on a pressurized pipe. A hot tap drilling machine is used to create a one

inch opening in the pipe wall. Once installed, this kit allows for insertion and removal of the flow

meter without a system shutdown.

Directions

1. Identify an appropriate location for the flow meter

(see pages 2-4).

2. Clamp the saddle onto the pipe; refer to

manufacturer’s instructions.

3. Install the close nipple and ball valve as shown

below. Use a paste type thread sealant. DO NOT

use Teflon

tape.

4. Use a hot tap drilling machine with a 1” hole saw

to drill the access hole.

5. Remove the drill; then flush all debris out of the

valve.

6. Use the 1” reducer provided in this kit when

installing the flow meter.

Important Note

ONICON insertion flow meters

are precision measuring devices

that must be installed according to

the instructions contained in this

document in order to maintain their

accuracy and reliability. Failure to

follow these instructions will result

in erratic operation and reduced

accuracy.

NOTE: Before installing the flow meter,

read the entire installation manual.

(see Sections 3.1 and 3.2).

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды