Onicon F-1100 Series Скачать руководство пользователя

Страница: 32 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 32

8-20-01

0272

1500 North Belcher Road, Clearwater, Florida 33765 Tel (727) 447-6140 Fax (727) 442-5699

www.onicon.com E-mail: [email protected]

FLOW METER WIRING INFORMATION

User Connections for Models with Non-Isolated Analog Outputs
Models: F-1110, F-1210, FB-1210 & F-1310

Wiring Information

WIRE COLOR CODE

NOTES

(+) 24 ± 4 V AC/DC
supply voltage

RED

BLACK

(–) Common ground
(Common with pipe ground)

Connect to power supply

negative & analog input

ground

GREEN

(+) Frequency output signal:
0-15 V peak pulse

Required when meter
is connected to local
display or BTU meter

BLUE

(+) Analog signal:
4-20 mA (non-isolated)

Both signals may be
used independently
(unless 0-5 V output
is ordered)

BROWN

(+) Analog signal:
0-10 V (non-isolated)
(Can also be ordered
as 0-5 V)

GRAY

VIOLET

Dry contact directional
output - indicates
flow direction

Contact closed when flow
is in direction of arrow
on meter

DIAGNOSTIC SIGNALS

ORANGE Bottom turbine frequency

WHITE

Top turbine frequency

These signals are for
diagnostic purposes -
connect to local display
or BTU meter

Connect to power supply
positive

√

F-1110

Single

Turbine

F-1310

Inline

F-1210

Dual

Turbine

FB-1210

Bi-Directional

FB-1210 Wiring Diagram

Connections to a Control System (No Display or BTU Meter)

RED

BLACK

BLUE

BROWN

GRAY

VIOLET

+ 24 V

COM

SIGNAL GROUND
ANALOG INPUT

Power

Source

Control System

BINARY (DIGITAL) INPUT

(Direction)

F-1110 / F-1210 / F-1310 Wiring Diagram

Connections to a Control System (No Display or BTU Meter)

RED

BLACK

BLUE

BROWN

+ 24 V

COM

SIGNAL GROUND

ANALOG SIGNAL INPUT

Power

Source

Control System

NOTES:

1. Serial Numbers 115691 and earlier require 24 VDC. Serial Numbers 115692 and higher

can accept 24 V AC/DC.

2. Black wire is common with the pipe (typically earth ground).

3. For ONICON display module or BTU meter, connect all wires provided. Refer to wiring diagram

provided with display or BTU meter.

4. This is NOT a "loop-powered" instrument. DO NOT connect power to any of the signal

output wires (blue, brown, green, orange or white)

FLOW METER

0272

08-01

CAUTION

This is NOT a “loop-powered” instrument. DO NOT connect power to any of the signal output

wires (blue, brown, green, orange or white)

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды