Onicon F-1100 Series Скачать руководство пользователя | Manualshive

Страница: 4 / 53

background image

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 4

SECTION 1.0: INTRODUCTION

We, at ONICON Incorporated, would like to thank you for purchasing our quality, U.S. made, Turbine
Flow Meter. As our valued customer, our commitment to you is to provide fast reliable service and
assistance, while continuing to offer you new products to meet your growing flow measurement needs.

1.1 PURPOSE OF THIS GUIDE

We have written this guide to provide the persons responsible for the installation, operation and
maintenance of your turbine flow meter with the most specific equipment information they will
need. This is NOT an electrical or plumbing trade manual.

WARNING

Please do not permit any persons to install, operate or maintain this equipment unless they have a

complete knowledge of their trade skills and are competent to work on high pressure hot and cold

water systems, according to their individual trades. Death or permanent injury may result from

accidents with these systems.

!

This guide is the basic reference tool for all ONICON Turbine Flow Meters. If you have not
purchased all of the options, there will be references in this manual which are not applicable to
your meter(s).

1.2 TYPICAL TURBINE FLOW METERS

ONICON’s Turbine Flow Meters measure the velocity
of flowing liquids by counting the frequency at
which the blades of a rotating turbine pass a fixed
electrode. Circuitry within the flow meter electronics
enclosure then converts the rotational rate to digital
and/or analog signals which are transmitted via
a connecting cable to any of ONICON’s display
devices, BTU meters and/or a data acquisition
system.

Sweat or NPT

Process Connections

Electronics Enclosure

Inline Meter

Insertion Meter

«
...
2
3
4
5
6
...
»

Содержание F-1100 Series






















































Отзывы:

Нет отзывов

Похожие инструкции для F-1100 Series

Бренд: Camille Bauer Страницы: 62

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: Olympus Страницы: 4

Бренд: Ulvac Страницы: 18

Бренд: Magnescale Страницы: 64

SourceMeter 2430

Бренд: Keithley Страницы: 141

Бренд: Oldham Страницы: 96

Universal Analyzers 275E

Бренд: Ametek Страницы: 34

Бренд: Topcon Страницы: 59

Бренд: OmegaWatt Страницы: 9

Engine Analyzer Series

Бренд: ACCEL DFI Страницы: 39

Бренд: Lambda Страницы: 35

Бренд: Hammerhead Страницы: 44

Бренд: wtw Страницы: 63

Бренд: az-instrument Страницы: 12

Бренд: Magnetrol Страницы: 48

TWIN LASER GB II

Бренд: Nicols Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды