Onicon F-1100 Series Скачать руководство пользователя

Страница: 37 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 37

WIRING DIAGRAM

INTERNAL CONNECTIONS FOR

DIVIDED OUTPUT FLOW METERS

MODELS F-1120 / F-1220 / F-1320

SENSING BOARD

DIVIDER BOARD

EXTERNAL CABLE CONNECTIONS

NOTES:

1:1

1:32

1:16

1:8

1:4

1:2

1:4096

1:2048

1:1024

1:512

1:256

1:128

1:64

1:1 JUMPER AT

THIS END

8-22-00

1500 North Belcher Road, Clearwater, Florida 33765 Tel (727) 447-6140 Fax (727) 442-5699

www.onicon.com E-mail: [email protected]

0069-1

AVAILABLE BINARY DIVIDER
SELECTIONS

SELECT ONLY ONE VALUE
OR THE DIVISION WILL
NOT BE CORRECT

TOP TURBINE:

F-1220 ONLY

(WHITE WIRE)

BOTTOM TURBINE:

F-1220 ONLY

(ORANGE WIRE)

(BROWN WIRE)
DIVIDED OUTPUT SWITCH
(BLUE WIRE)

FREQUENCY OUTPUT

(GREEN WIRE)

COMMON GROUND

(BLACK WIRE)

24V AC/DC SUPPLY

(RED WIRE)

EXTERNAL CABLE

NOTE: INTERNAL CONNECTIONS

OMITTED FOR CLARITY

TEST SIGNAL INPUT

1:1 JUMPER AT THIS END

DIVIDER JUMPER BLOCK

BLACK WIRE (BOARD TO BOARD)

GREEN WIRE (BOARD TO BOARD)

RED WIRE (BOARD TO BOARD)

For use with serial numbers

115692 and later

0069-1

08-00

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды