Onicon F-1100 Series Скачать руководство пользователя

Страница: 12 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 12

3.3 INSERTION METER MECHANICAL INSTALLATION

ONICON Insertion Turbine Flow Meters employ a hot tap adapter design that allows for

insertion and removal, when necessary, without interrupting flow and draining the pipe. To take

advantage of this feature, the flow meter must be installed through an isolation valve. The

installation must also allow for sufficient overhead clearance to fully extract the meter, and a full

1” opening in the pipe wall is required to clear the sensor head and allow for insertion. Make sure

that your valves and fittings are full port and at least 1” in actual internal diameter.

CAUTION

ONICON insertion style flow meters must be installed through a valve assembly. Failure to do so

negates the ability to remove the meter without shutting down flow and draining the system. It will

also result in an excessive amount of stem protruding from the pipe. Excessive stem lengths

unneccessarily expose the meter to incidental damage.

IMPORTANT NOTE

Flow meters installed through oversized access holes will be subjected to undesirable turbulence

that may affect the accuracy of the meter.

Typically

30" - 40"

depending on

pipe size and

height of valve

assembly.

CLEARANCE

REQUIRED

FOR INSTALLATION

Minimum Hole Size = 1"

Must be centered

Standard Installation

Kit for Steel Pipe

1" Full port ball valve
1" Close nipple
1" Branch outlet

1¼" for

hot tap

NOTE: Use stainless steel or brass

close nipple only.

23”- 36”

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды