Onicon F-1100 Series Скачать руководство пользователя

Страница: 42 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 42

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699

www.onicon.com • [email protected]

09-08

0540-1

Do not

substitute threaded tees for

the welded branch outlet. Contact

ONICON if you need installation

hardware for threaded pipe.

Installation Hardware Instructions
Hot Tap Installation Kit for Welded Steel Pipe

For F-1100, F-1200 & FB-1200 Series Insertion Turbine Flow Meters

This kit can be installed on a pressurized pipe. A hot tap drilling machine is used to create a one

inch opening in the pipe wall. Once installed, this kit allows for insertion and removal of the flow

meter without a system shutdown.

For Use With Kits: INSTL2, INSTL6, INSTL31

Directions

1. Identify an appropriate location for the flow

meter (see pages 2-4).

2. Weld the branch outlet onto the pipe.

3. Install the close nipple and ball valve as shown

below. Use a paste type thread sealant. DO

NOT use Teflon® tape.

4. Use a hot tap drilling machine with a 1” hole

saw to drill the access hole.

5. Remove the drill; then flush all debris out of

the valve.

6. Use the 1” reducer provided in this kit when

installing the flow meter

NOTE: Before installing the flow meter, read the entire

installation manual.

Important Note

ONICON insertion flow meters

are precision measuring devices

that must be installed according to

the instructions contained in this

document in order to maintain their

accuracy and reliability. Failure to

follow these instructions will result

in erratic operation and reduced

accuracy.

(see Sections 3.1 and 3.2).

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды