Onicon F-1100 Series Скачать руководство пользователя

Страница: 41 / 53

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699 • [email protected]

Turbine Flow Meter Manual 05/13 - 0721-1 / 13518

Page 41

1500 North Belcher Road, Clearwater, FL 33765 • Tel (727) 447-6140 • Fax (727) 442-5699

www.onicon.com • [email protected]

Installation Hardware Instructions
Standard Installation Kit for Welded Steel Pipe

For F-1100, F-1200 & FB-1200 Series Insertion Turbine Flow Meters

IMPORTANT NOTE

ONICON insertion

ow meters are

precision measuring devices that

must be installed according to the

instructions contained in this

document in order to maintain their

accuracy and reliability. Failure to

follow these instructions will result

in erratic operation and reduced

accuracy.

0536-1/15950

9-5-08

This kit must be installed prior to

lling the system, or into a section of pipe that is isolated from

pressure and

ow. Once installed, this kit allows for insertion and removal of the

ow meter without

a system shutdown.

Do not

substitute threaded tees for

the welded branch outlet. Contact

ONICON if you need installation

hardware for threaded pipe.

For Use With Kits: INSTL1, INSTL5, INSTL18

Directions

1. Identify an appropriate location for the

meter (see pages 2-4).

2. Weld the branch outlet onto the pipe.

3. Drill a one inch (minimum) access hole,

centered in the branch outlet.

4. Install the close nipple and ball valve as

shown below. Use a paste type thread

sealant. DO NOT use Te

tape.

5. Flush and

ll the system prior to installing the

ow meter.

NOTE: Before installing the

ow meter, read the entire installation manual.

(see Sections 3.1 and 3.2).

Содержание F-1100 Series






















































Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды

Onicon F-1100 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F-1100 Series

Отзывы:

Похожие инструкции для F-1100 Series

Бренды по названию

Популярные бренды