![background image](http://html.mh-extra.com/html/omron/e5c-series/e5c-series_user-manual_742592358.webp)
A Appendices
A - 32
E5@C Digital Temperature Controllers User’s Manual (H174)
*1
Initialized to input setting range upper and lower limits, or scaling upper and lower limits.
*2
Clamped by SP upper and lower limits.
*3
This parameter is initialized only when the input type is changed to analog input when the RT parameter is ON. The RT
parameter turns OFF.
*4
Initialization is performed as shown below according to the transfer output type setting. The initialization differs
depending on the changed parameter and the output type setting.
• SP: SP upper and lower limits
• Ramp SP: SP upper and lower limits
• PV: Input setting range upper and lower limits or scaling upper and lower limits
• MV (Heating): 100.0/0.0
• MV (Cooling): 100.0/0.0
• Valve opening: 100.0/0.0
*4.1 Initialized only when the transfer output type is set to SP, Ramp SP, or PV.
*4.2 Initialized only when the transfer output type is set to MV (Heating) or MV (Cooling).
*4.3 Initialized to the above default values regardless of the settings for changing the transfer output type.
*5
Initialized as follows according to the Standard or Heating/Cooling parameter setting.
• MV Upper Limit: 100.0
• MV Lower Limit: Standard 0.0, heating/cooling
−
100.0
*6
Initialized to control output (cooling) for heating and cooling control, according to the following.
(The defaults for standard control are the defaults in the parameter list.)
• With control output 2: The Control Output 2 Assignment parameter is initialized to control output (cooling).
• If the Controller does not have control output 2 but has four auxiliary outputs, the Auxiliary Output 4 Assignment
parameter is initialized to Control Output (Cooling).
• If the Controller does not have control output 2 but has two auxiliary outputs, the Auxiliary Output 2 Assignment
parameter is initialized to Control Output (Cooling).
• Otherwise, the Auxiliary Output 2 Assignment parameter is initialized to Control Output (Cooling).
*7
If the Program Pattern parameter is set to OFF, the Auxiliary Output 1 Assignment parameter is initialized as follows:
• Controllers with HB and HS alarms: Heater alarm
• Controllers without HB and HS alarms: Alarm 1
If the Program Pattern parameter is not set to OFF, the Auxiliary Output 1 Assignment parameter is initialized to the pro-
gram end output.
*8
If the Program Start parameter is assigned when the program pattern is changed to OFF, the Program Start parameter
will be initialized to "not assigned."
Event Input
Assignment 1 to 6
---
---
---
---
---
---
●
*8
---
---
---
---
---
---
---
---
---
---
Move to Protect Level
---
---
---
---
---
---
---
---
---
---
---
---
---
---
●
*10
---
---
MV Display Selection
---
---
---
---
---
●
---
---
---
---
---
---
---
---
---
---
---
Position Proportional
Dead Band
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
●
*20
---
Dead Band
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Hysteresis (Heating)
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Hysteresis (Cooling)
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Wait Band
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Alarm 1 to 4 Hysteresis
●
*14
---
---
---
---
---
---
---
---
---
---
---
●
*15
---
---
---
---
ST Stable Range
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
AT Hysteresis
●
*13
*18
●
*18
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
LBA Level
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
LBA Band
●
*13
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
In
pu
t T
y
pe
T
e
mpe
rature Un
it
Scalin
g L
o
w
er Lim
it
Scalin
g Up
per L
imit
SP Lo
w
e
r Limit
SP Upper Limit
PID ON/OFF
Stan
dar
d
or
Heat
ing
/Coo
ling
Pr
ogram P
a
ttern
ST
Remote SP E
n
ab
le
T
ransf
er Outpu
t T
y
pe
RT
Int
egral/D
eriv
at
ive Tim
e Un
it
Alarm
1 to
4 T
yp
e
SP 0 to 7
Set P
o
int
P
ass
w
o
rd
to Mo
ve to
Pr
o
tect Le
vel
C
los
e
/F
loa
ting
Direct Setti
ng o
f P
o
sition
Pr
o
por
tio
n
al MV
Related
initialized
parameters
Changed
parameter
Содержание E5C series
