![background image](http://html.mh-extra.com/html/omron/e5c-series/e5c-series_user-manual_742592107.webp)
4 - 9
4 Basic Operation
E5@C Digital Temperature Controllers User’s Manual (H174)
4-
2 Init
ial Sett
ing
E
x
amp
les
4
*
If the Controller is equipped with HB/HS alarm detection, the Alarm 1 Type is not displayed for the default
settings. To use alarm 1, set an output assignment to alarm 1. For details, refer to 4-6-3 Assigned Output
Functions (Assigning Control Outputs Is Not Supported for Position-proportional Models.).
Example 2
0
25
M
M
M
M
9
in-t
pid
cntl
2
alt1
150
25
M
off
st
20
cp
off
at
M
M
M
150
25
run
r-5
30
al-1
Set SP
9
20
30
2
150
onof
pid
on
off
off
run
stop
Input type:
9 (T thermocouple,
−
200
°
C to 400
°
C)
Control method:
PID control
PID constants found using auto-tuning (AT).
Alarm type:
2 (upper limit)
Alarm value 1:
30
°
C
Set point:
150
°
C
Setup Procedure
Power ON
Initial Setting Level
Set input
specifications
Set control
specifications
Set alarm type
Adjustment Level
AT execution
(When PID control
is selected)
Operation Level
Set alarm value
Start operation
Power ON
Operation Level
PV/SP
Press the
O
Key for at least 3 s.
Control stops.
Initial Setting Level
Use the
U
and
D
Keys to select the
input type.
Input Type:
Use the
U
and
D
Keys to select
PID control.
ON/OFF control:
Use the
U
and
D
Keys to set ST
to OFF.
To execute ST:
PID control:
To cancel ST:
Check the
control period.
Control Period
(Heat)
(Unit: Seconds)
Check the
alarm type.
Alarm 1 Type*:
For PID, set
pid
.
It is recommended that 20 seconds
be set for a relay output and 2
seconds for an SSR voltage output.
When a linear current output is
used, the Control Period parameter
cannot be used.
Press the
O
Key for at least 1 s.
Operation Level
Use the
U
and
D
Keys to set the SP
to 150
°
C.
PV/SP:
Adjustment Level
Execute AT.
To execute 100%AT:
To cancel AT:
Press the
O
Key (for less than 1 s).
Press the
O
Key (for less than 1 s).
Control starts.
Operation Level
Confirm that the
set point is 150
°
C.
PV/SP
Confirm that
control is running.
Running
Stopped
Use the
U
and
D
Keys to set the alarm
value to 30
°
C.
Alarm
Value 1
Start operation.
at-1
To execute 40%AT:
at-2
Operation Level
An
s.err
error will be displayed if
the power supply is turned ON
before the sensor is connected.
The TUNE indicator will
light during autotuning.
Содержание E5C series
