Omron Cobra 350 CR/ESD Скачать руководство пользователя | Manualshive

Страница: 117 / 138

background image

Chapter 8: Maintenance

enable high power until the lamp has been replaced. Follow this procedure to replace the High
Power indicator lamp. The part number for the lamp is 27400-29006.

WARNING:

ELECTROCUTION RISK

Lock out and tag out power before servicing.

WARNING:

ELECTROCUTION RISK

The procedures and replacement of parts mentioned in this section should be
performed only by trained, authorized personnel. The access covers on the
Front Panel are not interlocked – turn off and disconnect power before remov-
ing the cover.

1. Turn off system power to the robot.

2. Turn off power to the optional SmartController EX, if you are using one.

3. Disconnect the cable between the Front Panel and the eMB-40R (or controller).

4. Remove the Front Panel from its mounting location.

5. Remove the two screws on the back of the Front Panel.

Save the screws for re-installation.

6. Carefully pull the front cover away from the body of the Front Panel.

You will encounter some resistance, as there are three plug-type connectors that you
need to disconnect as you pull the front cover away from the body.

NOTE:

Separate the cover from the body slowly to avoid damaging the

two wires that go between the LED and the PC board inside the body. Pull
the front cover as straight out as possible. You do not have to disconnect
the wires from the PC board, although you can if needed.

7. Locate the lamp body in the center of the back side of the front cover. Turn the lamp

body approximately 20° in either direction and then pull straight back.

8. The lamp body is now free. You can remove the old lamp and insert a new one.

9. Re-install the lamp body by pushing it straight into the lamp housing receptacle. Make

sure the contacts on the lamp body are properly oriented, as shown in the following fig-
ure.

10. Make sure to reconnect the wires from the LED if you disconnected them earlier.

11. Push the front cover into the body, taking care to align all of the plug-type connectors.

Verify that the wires do not get crimped as you reinstall the cover.

12. Re-install the two screws on the back of the body.

13. Re-install the Front Panel in its mounting.

14. Reconnect the cable between the Front Panel and the eMB-40R (or controller).

05624-000 Rev. K

Cobra 350 User's Guide

117

«
...
115
116
117
118
119
...
»

Содержание Cobra 350 CR/ESD











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cobra 350 CR/ESD

KR QUANTEC extra

Бренд: Kuka Страницы: 127

Бренд: adept technology Страницы: 18

Бренд: YZ Robot Страницы: 20

Rexroth APAS assistant K1100-10i

Бренд: Bosch Страницы: 68

Бренд: Bosch Страницы: 64

Comprehensive Kit Robot Series

Бренд: Robotis Страницы: 197

Бренд: HEBI Robotics Страницы: 36

Бренд: 4tronix Страницы: 9

Бренд: Mab Robotics Страницы: 35

TIGER ELECTRONICS Robo-Chi Pets Series

Бренд: Hasbro Страницы: 2

YR-1-06VX50-A00

Бренд: YASKAWA Страницы: 86

Бренд: SCHUNK Страницы: 28

Бренд: SCHUNK Страницы: 32

Бренд: Steren Страницы: 13

Бренд: Steren Страницы: 16

Бренд: Steren Страницы: 18

Бренд: Steren Страницы: 22

Бренд: Steren Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды