background image

Chapter 8: Maintenance

Teach Restrict Configuration Utility

This utility sets the hardware Teach Restrict maximum speed parameter to factory spe-
cifications.

NOTE:

Ensure that the commissioning jumper is plugged into the XBELTIO jack

on the eMB-40R before you start this procedure.

Procedure

NOTE:

This procedure takes 2 or 3 minutes to complete.

From within the ACE software:

1. Open the robot object editor.

2. Select

Configure > Safety Settings > Configure Teach Restrict

, then click Next.

3. From the Prerequisite screen, click Next.

The wizard will go through all of the robot's motors, and display messages that it is con-
figuring Channel A and B for each.

It will then record the configuration, and display the target times that it set.

4. Click Finish.

5. Reboot the controller.

On some systems, the controller will reboot automatically.

Teach Restrict Verification Utility

This utility verifies that the Teach Restrict parameters are set correctly and that the hardware
Teach Restrict maximum speed control is working.

This is a two-part wizard. The first is run in Auto mode. The second is run in Manual mode.

Before running this verification utility, the Teach Restrict must be configured.

NOTE:

If the commissioning jumper is plugged into the XBELTIO jack on the

eMB-40R, remove it before you start this procedure.

Automatic Mode Procedure

!

WARNING:

PERSONAL INJURY RISK

The robot will move during this wizard. Ensure that personnel stay clear of the
robot work area.

From within the ACE software:

1. Open the robot object editor.

2. Select

Configure > Safety Settings > Verify Teach Restrict

, then click Next.

05624-000 Rev. K

Cobra 350 User's Guide

115

Содержание Cobra 350 CR/ESD











































































































































Отзывы: