background image

9

Installation

of suitable capacity. For weight information 

please see Technical Specifications; 

Weight data are also stated on the mixer 

identification plate; Slip the lifting fork into 

the special grooves at the base of the pallet/

crate/cage until they protrude by at least 

200mm on the opposite side.

PLEASE NOTE:

Do not use handling systems, tools and 

equipment other than those that are 

described herein. When handling and / 

or transporting the mixer or parts thereof 

take all the necessary precautions to 

avoid, or minimize, the occurrence 

of risks to people, animals, and other 

assets.

Remove the machine from its packaging, separating the materials by type (plastic, wood, etc.) and deliver 

them to dedicated collection areas, assigned to authorized persons for disposal in accordance with current 

environmental laws and regulations. Check the machine and make sure there are no missing parts; if in doubt, 

consult the manufacturer. To remove an unpacked mixer from the pallet, crate, or cage, lift it up using a strap 

of adequate capacity (the weight of the machine is indicated on the plate as well as in this manual) slipped 

underneath the mixer head at the outlet (see Figure 7) and hooked up to a lifting device of adequate capacity 

(jib cranes, bridge cranes, etc.). The strap should be compliant to the relevant legal requirements and must 

have a maximum width of 40mm and a length so that each connecting length from below the head of the 

base to the hook of the lifting device is at least equal to 1200mm; so that the band remains flat and as close 

as possible to the column of the base. 

It is forbidden to hang up the strap to the tips of a lifting fork as 

it might slip off

 and break away with consequent fall of the mixer and risk of injuries to the bystanders; Also 

avoid swinging of the suspended mixer that may cause instability of the forklift.

Lift the machine gently, avoiding jolts and vibrations; once raised it could tip slightly; this is absolutely normal. 

Содержание MX-IT-0060-M





























Отзывы: