Oki MC160MFP, Руководство по обслуживанию

Страница: 175 / 207

44292401TH Rev.1
174 /
Oki Data CONFIDENTIAL
ADJUSTMENT/SETTING
16.4 How to analyze the T30 protocol monitor
• DCS or DIS
• HEX Data as printed on page.
See P.134
• Example: V .17 Communication
• FIF (Facsimile Information Field)
• Hex-Binary Conversion List
NAME: ABC
TEL:886 3 4733507
DATE: APR.23’04 12:20
SESSION FUNCTION NO DESTINATION STATION DATE TIME PAGE DURATION MODE RESULT
0001 TX 01
ABC
2234567
8 901234567 890
DEC.02 15:00 00 8 00h00min00s ECM-12 OK
TX RX DATA
FF 13 83 00 46 88 00
...
PROTOCOL MONITOR REPORT
FCF (Facsimile Control Field)
= 83: DCS, 80: DIS
FIF (Facsimile Information Field)
Means Last Control Field.
Means address
HEX
1 2
0 0 4 6 8 8 0 0
Data Bit
0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0
Bit No.
8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9 24 23 22 21 20 19 1 8 19 32 31 30 29 2 8 27 26 25
Note
Bit No.11= 1, Bit No.12=0 7200 bps
Bit No.15= 1 R
8 x 7.7 Lines/mm (Fine Mode)
Bit No.19= 0, Bit No.20=1 Unlimited Paper Length
n n n n n
Hex Binary Hex Binary Hex Binary Hex Binary
0 0 0 0 0 4 0 1 0 0 8 1 0 0 0 C 1 1 0 0
1 0 0 0 1 5 0 1 0 1 9 1 0 0 1 D 1 1 0 1
2 0 0 1 0 6 0 1 1 0 A 1 0 1 0 E 1 1 1 0
3 0 0 1 1 7 0 1 1 1 B 1 0 1 1 F
1 1 1 1
16.3 Table of reference code
Code Function
CFR Confirmation to Receive. 1
8
50 Hz or 1650 Hz 3 sec.
CIG Calling Station Identification.
CRP Command Repeat.
CSI Called Subscriber Identification.
DCN Disconnect.
DCS Digital Identification Signal.
DIS Digital Transmit Command.
DTC Digital Transmit Command.
EOM End of Message. 1,100 Hz.
EOP End of Procedure.
FTT Failure to Train.
MCF Message Confirmation. 1,650 Hz or 1,
8
50 Hz.
MPS Multi-Page Signal.
NCS Non-Standard Facilities Command.
NCF Non-Standard Facilities.
NSS Non-Standard Facilities Set-up.
PIN Procedural Interrupt Negative.
PIP Procedural Interrupt Positive.
PRI-EOM Procedure Interrupt-End of Message (COM).
PRI-MPS Procedure Interrupt-Multi page Signal (MPS).
PRI-EOP Procedure Interrupt-End of Procedure (EOP).
RTN Retrain Negative.
RTP Retrain Positive.
TSI Transmitting Station Identification.
15.3 Table of reference code 15.4 How to analyze the T30 protocol monitor