Oki MC160MFP, Руководство по обслуживанию

Страница: 138 / 207

44292401TH Rev.1
137 /
Oki Data CONFIDENTIAL
ADJUSTMENT/SETTING
15.2.2 Soft switch list
Soft Switch No. Bit No. Designation Page No.
#01 2/1
V
.34 CI signal byte number P.150
#02
8
/7 Time between phase C to phase D signal in
V
.17
P.150 6 Header TX selection open to user
3/2 Transmit RTN signal level criteria
#03
8
Send out NSF frame with station ID
P.151
7 Number of Pause within phone number
6 Re-dial prohibit for NO ANSWER
4/3/2/1 RX level setting
#04
4
V
isible alarm for RTN signal
P.151
3 Audible alarm for RTN signal
#05
8
/7 Push button ON/OFF Timing (PB)
P.152
6/5 Relation between 10 key # & No.of dial pulse
3 10PPS/20PPS
2/1 PPS ratio
#06
8
/7 Ring on time to ignore ring off time at 1st cycle
P.152
4/3 Ring off time at 1st cycle to approve incoming ring
#07
8
Dial tone or busy tone detection
P.152
7 PSTN/PBX setting
6 PBX dial tone detect
5 Dial mode select
4/3/2/1 TX level select for PSK/FSK
#0
8
7 Detect busy tone after dialing
P.153
6 Sending CED signal after connection
#09
8
/7 Ringer frequency detection
P.153 5
T
SI/CSI append “+”
2/1 Time from RX DIS signal to send DCS signal
#10
8
Print out RTN page report
P.153
7 Confirmation report result field
6/5 Get gap time between digit for pulse dial
4 RX PIP T.30 command after send out MPS command
3 Received DIS signal within reception
2 Transmission time limitation
1 Audio alarm after communication fail
#11
7 Detect dial tone after pre-fix number
P.154
6 Pulse dial allowed to select
5 Protocol signal display mode
2 USB port number fixed
1 DTMF low frequency compensation
Soft Switch No. Bit No. Designation Page No.
#12
8 ECM mode capability
P.154
7/6 V.34 fall back counter for V.34 TX
5 Send CTC after 4th PPR
3 Send EOR after lowest speed
2/1 TCF transmission timing after DCS signal
#13
8 MR capability for G3
P.155
7/6 Delay time between transaction
5 Super fine printing capability for receiving
3 DTS mode
2
Send DTC signal if RX DIS signal in manual RX mode
(no function on G4)
#14
6 Memory size level to RX
P.155
3/2/1 Time between V.34 ANSam signal and FSK DIS signal
#15
8 IPSEL1
P.155 7 DCSEL
6 DCLIM
#16 2/1 Fax communication coding method P.155
#17
6 CED frequency
P.156 5/4/3 Pause between off hook and CED signal
2/1 Inactivity timer [T5]
#18
6/5 G3 mode training quality level
P.156
4/3/2/1 Redefine re-dial attempts counter
#19
8/7/6/5 CNG signal level
P.157
4/3/2/1 DTMF high frequency level
#20
—
Reserved P.157
#21
8 NSS signal before DCS
P.157
7/6 CNG sending duration after dialing
5 T4 timer
4 VOIP (Voice over IP)
3 DIS signal length
2/1 Increase default T1 timing during calling (Only for TX function)
#22 4/3/2/1 CED signal output level P.158
#23 4/3/2/1 DTMF low frequency level P.158
#24
7/6/5/4/
3/2/1
Re-dial interval P.158
#25 4/3 Flash key time P.159
#26 8/7 Dial tone detection time before disconnected P.160
#27
—
Reserved P.160
#28
8/7/6/5 Time to dial after dial tone on the line
P.160
4/3/2/1 CED duration time within calling period
#29 5/4/3/2/1 Time to dial after seize the line when dial tone detection P.161
14.2.2 Soft switch list