Ofs Obeya Скачать руководство пользователя страница 43

Страница: 43 / 44

ofs.com

imagine a place®

800.521.5381

Assembly instructions

Obeya assembly instructions

1. Place receptacle housing into panel from

front side.

2. From back side of panel secure receptacle

housing to panel with (4) #8-32 x 1/2" machine
screws and (4) flat washers.

3. From back side of panel place duplex receptacle

into housing.

4. Locate back plate centered over the back of teh duplex

receptacle aligning holes in the back plate with inserts
in the back of the receptacle housing.

5. WARNING! Do not over tighten screws.

Secure back plate to receptacle housing using (4)
#8-32 X 3/8" machine screws.

Detail B

Scale 1 : 2

#8-32 x 1/2"
Machine screw
& flat washer

#8-32 x 1/2"
Machine screw

Back plate

Duplex receptacle

Duplex receptacle assembly - full wall panel

Receptacle
housing

Содержание Obeya













































Результаты поиска

Содержание Obeya

Отзывы:

Похожие инструкции для Obeya

Бренды по названию

Популярные бренды

Ofs Obeya, Руководство по сборке

Результаты поиска

Содержание Obeya

Отзывы:

Похожие инструкции для Obeya

Бренды по названию

Популярные бренды