Ofs Obeya Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 44

background image

29

ofs.com

imagine a place®

800.521.5381

Assembly instructions

Obeya assembly instructions

Connector nut

Connector bolt

Connector bolt

Beam access slot

5/16-18 x 3/4" Bolt &
5/16 flat washer

Framed wall panel attachment - continued

Multi panel full wall

Note:

Panel to panel connection.

Wood infill to wood infill: 2.75" connector
bolt & connector nut

Wood infill to metal infill: 3" all-thread &
2 connector nuts

Metal infill to metal infill: 3.5" all thread &
2 connector nuts.

3. Secure the framed panel assembly to the post using the 1/4-20 x 2.75" connector bolts. Insert one

bolt into each of the holes in the framed panel vertical rail and thread into the insert nuts into the
post edge leaving loose for panel adjustment.

4. If a two module wall move to step 6. For three module walls place the center panel in place and

repeat step 2.

5. Slide the center panel tight againt the first panel and secure using the panel to panel connection

method noted below. Tightening the fasteners to close any gap between the two vertical frame
rails of both panels.

6. Move the last framed wall panel into place ensuring the light sill extrusion on the post engages in

the groove on the framed panel vertical rail and repeat steps 2 & 3.

Panel to post
connection

Panel to panel
connection

«
...
27
28
29
30
31
...
»

Содержание Obeya













































Отзывы:

Нет отзывов

Похожие инструкции для Obeya

Бренд: UltraHD Страницы: 13

Бренд: Walker Edison Страницы: 11

Бренд: Oypla GARDEN Страницы: 3

Бренд: Safco Страницы: 2

Бренд: E-Z UP Страницы: 2

Бренд: Gami Страницы: 15

Бренд: SALICE Страницы: 40

Бренд: Safavieh Страницы: 4

Бренд: Safavieh Страницы: 3

SYNERGY SYSTEM SLC20

Бренд: Salamander Designs Страницы: 5

Бренд: realspace Страницы: 81

Бренд: Furinno Страницы: 2

LIVE EDGE BE-9014TA

Бренд: Unfinished Furniture of Wilmington Страницы: 5

L-DN1210SST-E-T

Бренд: Sunjoy Страницы: 3

Бренд: Uberhaus Страницы: 52

T-BENCH 411/78.1950.22

Бренд: dB Страницы: 6

FlexFit Hyken UN59461

Бренд: UNION & SCALE Страницы: 12

IndaMatic EUROPA 2

Бренд: Indaux Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды