Ofs Obeya Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

background image

30

ofs.com

imagine a place®

800.521.5381

Assembly instructions

Obeya assembly instructions

Connector nut

Connector bolt

Connector bolt

Beam access slot

5/16-18 x 3/4" Bolt &
5/16 flat washer

Framed wall panel attachment - continued

Multi panel full wall

Note:

Panel to panel connection.

Wood infill to wood infill: 2.75" connector
bolt & connector nut

Wood infill to metal infill: 3" all-thread &
2 connector nuts

Metal infill to metal infill: 3.5" all thread &
2 connector nuts.

7. Tighten the fasteners for panel to panel connections so the vertical rails of both panels are

fastened tight.

8. Shift the wall panel set so that there is an equal tolerance gap on each end between the outer

framed panels and posts.

9. Secure the 5/16-18 x 2.75" bolts in the vertical rails into the posts. Snug the bolt head to the inside

face of the framed panels vertical rail. Do not over tighten as this can warp the frames.

10. Extend the adjustable glides out so that they are snug against the floor. Use the glide extention

cups for each increment over 1/2" of adjustment needed.

11. Go back and tighten the 5/16-18 x 3/4" bolts in the mounting rails of all panels.

Panel to post
connection

Panel to panel
connection

«
...
28
29
30
31
32
...
»

Содержание Obeya













































Отзывы:

Нет отзывов

Похожие инструкции для Obeya

Бренд: Xo Страницы: 5

Бренд: Wholesale Interiors Страницы: 2

Бренд: UltraHD Страницы: 13

Бренд: Native Trails Страницы: 2

Бренд: Vamo Страницы: 3

Бренд: µ-Dimension Страницы: 3

Бренд: µ-Dimension Страницы: 3

Бренд: µ-Dimension Страницы: 5

Бренд: µ-Dimension Страницы: 3

JAIME HAYON MEZCLA JH20

Бренд: &Tradition Страницы: 5

Isole NN1A-NN1G

Бренд: &Tradition Страницы: 5

Бренд: &Tradition Страницы: 2

In Between Round and square top with wooden legs by Sami...

Бренд: &Tradition Страницы: 5

Бренд: Zanzini Страницы: 3

Бренд: Monarch Specialties Страницы: 3

BRONX LIGHT SHOE DROP 183382

Бренд: Next Страницы: 16

Miliano DTB 1404

Бренд: Safavieh Furniture Страницы: 3

Morgan Office Chair

Бренд: John Lewis Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды