Ofs Obeya Скачать руководство пользователя страница 31

Страница: 31 / 44

ofs.com

imagine a place®

800.521.5381

Assembly instructions

Obeya assembly instructions

1. Once all posts and extrusions are installed for the structure and leveled and electrical is installed

the split wall panels where applicable can be installed.

2. Lift panel into position against the top rail and cross rail with the top of the split wall panel

being approx 1" above the top of the top rail.

3. Applying pressure to the face of the wall panel at the top & bottom of the panel allow the panel

to slide downward into place. Ensuring all panel clips have engaged with the top rail and cross
rail hanging ledges before releasing panel.

Note

: Lifting the wall panel too high will cause the

panel clip to catch on the top of the extrusion causing a false sense of engagement. Top of wall
panel should be flush with top of top rail when seated correctly.

4. Secure wall panel using a tie down clip by aligning the rectangle nut with the t-slot in the top

rail closest to the panel.

5. Slide the tie down clip into position in the back of the panel rotating the clip into the slot as

you align it.

6. Secure by tightening the #8-32 screw in the clip.

Panel clip

Tie down slot

Split wall panel

Cross rail

Hanging ledge

Panel clip

Top rail

Hanging ledge

Panel clip

Split panel tie down clip

Split wall panel installation

Содержание Obeya













































Результаты поиска

Содержание Obeya

Отзывы:

Похожие инструкции для Obeya

Бренды по названию

Популярные бренды

Ofs Obeya, Руководство по сборке

Результаты поиска

Содержание Obeya

Отзывы:

Похожие инструкции для Obeya

Бренды по названию

Популярные бренды