55
Inverter swimming pool heat pump
GB
12
WARNING: Installation must be carried out by a qualified engineer.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.
3.6 Hydraulic connection
By-Pass assembly
The heat pump must be connected to the pool by means of a
By-Pass assembly.
A By-Pass is an assembly consisting of 3 valves that
regulate the flow circulating in the heat pump.
During maintenance operations, the By-Pass permits the heat
pump to be isolated from the system without interrupting your
installation.
Making a hydraulic connection with the By-Pass kit
WARNING: Do not run water through the hydraulic circuit for 2 hours after applying the adhesive.
Step 1: Take the necessary steps to cut your pipes.
Step 2: Make a straight perpendicular cut through the PVC pipes with a saw.
Step 3: Assemble your hydraulic circuit without connecting it in order to check that it perfectly fits your
installation, then dismantle the pipes to be connected. Step 4: Chamfer the ends of the cut pipes with sandpaper.
Step 5: Apply stripper to the ends of the pipes to be connected. Step 6: Apply the adhesive in the same place.
Step 7: Assemble the pipes.
Step 7: Clean off any adhesive remaining on the PVC.
Step 8: Leave to dry for at least 2 hours before putting the hydraulic circuit into water.
TOWARDS the pool
FROM the pool
Out
In
11
3.3 Installation layout
3.4 Connecting the condensation draining kit
While operating, the heat pump is subject to condensation. This will result in a more or less large run-off of
water, depending on the degree of humidity. To channel this flow, we recommend that you install the
condensation drainage kit.
How do you install the condensation drainage kit|?
Install the heat pump, raising it at least 10 cm with solid water-resistant pads, then connect the drainage pipe to
the opening located under the pump.
3.5 Installing the unit on noise-damping supports
In order to minimize the noise pollution associated with heat pump vibrations, it can be positioned on vibration
absorbing pads.
To do this, you simply have to position a pad between each of the unit’s feet and its support, and then fix
the heat pump to the support with suitable screws.
Half open valve
Open valve
11
3.3 Installation layout
3.4 Connecting the condensation draining kit
While operating, the heat pump is subject to condensation. This will result in a more or less large run-off of
water, depending on the degree of humidity. To channel this flow, we recommend that you install the
condensation drainage kit.
How do you install the condensation drainage kit|?
Install the heat pump, raising it at least 10 cm with solid water-resistant pads, then connect the drainage pipe to
the opening located under the pump.
3.5 Installing the unit on noise-damping supports
In order to minimize the noise pollution associated with heat pump vibrations, it can be positioned on vibration
absorbing pads.
To do this, you simply have to position a pad between each of the unit’s feet and its support, and then fix
the heat pump to the support with suitable screws.
While in operation, the heat pump is subject to condensation. That will result in a more or
less large run-off of water, depending on the degree of air humidity. To channel this fl ow,
we recommend the installation of a condensation draining kit.
How do you install the condensation draining kit?
Install the heat pump by means of solid, water-resistant pads raising it at least 10 cm.
Then connect the supplied condensate pipe incl. hose nozzle to the round drain opening
in the base plate / condensate tray located under the pump.
Also see Section 3.3 Position of condensation drain.
In order to minimise the noise pollution associated with heat pump vibrations, it can be
positioned on vibration-absorbing pads.
For this, you simply have to position a pad between each of the unit’s feet and its support,
and then fi x the heat pump to the base support with suitable screws.
Connection of condensation
draining kit
3.4
Installation of
vibration dampers
3.5
Hydraulic connection
3.6
IMPORTANT:
Installation must be carried out by qualifi ed technicians. This section is
provided for information purposes only and has to be checked and adap-
ted according to the installation conditions on-site if necessary.
Bypass kit
The heat pump must be connected to the pool by means of a bypass assembly.
A bypass is an assembly group consisting of 3 valves that regulate the fl ow circulation in
the heat pump.
During maintenance operations, the bypass valves allow for the heat pump to be isolated
from the system without having to interrupt the operation of the system.
