Oce ColorStream Скачать руководство пользователя страница 454

Страница: 454 / 524

Replacing the Smoothing Rollers

Replacing the smoothing rollers — overview

Note:

The 'Replace smoothing roller' menu is released by Service if necessary. The smoothing
rollers are to be replaced if:

■

the bearings of the smoothing rollers are stiff or heavily worn

■

significant signs of wear or damage are visible or noticeable on the surface of the
smoothing rollers

■

significant differences in the level of smoothness are identifiable over the paper width

■

paper path problems occur that can be traced back to the smoothing rollers.

Attention:

■

Switch off the paper post-processing unit/ensure that the paper web cannot be advanced
by the paper post-processing unit any more.

■

The replacement procedure can only take place when printing is stopped.

■

Smoothing rollers may only be used for the purpose for which they were originally
intended.

■

If the smoothing rollers had a very short service life, the cause of the damage must be
clarified in order to prevent further damage.

Overview

You will find information on the following topics:

■

‘Removing the smoothing rollers’

on page 455

■

‘Installing smoothing rollers’

on page 461

Chapter 9 - Replacing Expendables

454

Replacing the smoothing rollers — overview

Содержание ColorStream













































































































































































































































































































































































































































































































































Результаты поиска

Содержание ColorStream

Отзывы:

Похожие инструкции для ColorStream

Бренды по названию

Популярные бренды

Oce ColorStream, Руководство пользователя

Результаты поиска

Содержание ColorStream

Отзывы:

Похожие инструкции для ColorStream

Бренды по названию

Популярные бренды