manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MPC5605BK Скачать руководство пользователя страница 870

Chapter 30 Flash Memory

MPC5606BK Microcontroller Reference Manual, Rev. 2

870

Freescale Semiconductor

 

Throughout this document, several important terms are used to describe the platform flash memory 
controller module and its connections. These terms are defined here:

•

Port

 — This is used to describe the AMBA-AHB connection(s) into the platform flash memory 

controller. From an architectural and programming model viewpoint, the definition supports as 
many as two AHB ports, even though this specific controller only supports a single AHB 
connection.

•

Bank

 — This term is used to describe the attached flash memories. From the platform flash 

memory controller’s perspective, there may be one or two attached banks of flash memory. The 
code flash memory is required and always attached to bank0. Additionally, there is a data flash 
memory attached to bank1. The platform flash memory controller interface supports two separate 
connections, one to each memory bank.

•

Array

 — Within each memory bank, there is one flash memory array instantiations.

•

Page

 — This value defines the number of bits read from the flash memory array in a single access. 

For this controller and memory, the page size is 128 bits (16 bytes).

The nomenclature “page buffers and “line buffers” are used interchangeably.

30.7.1.1

Overview

The platform flash memory controller supports a 32-bit data bus width at the AHB port and connections 
to 128-bit read data interfaces from two memory banks, where each bank contains one instantiations of the 
flash memory array. One flash memory bank is connected to the code flash memory and the other bank is 
connected to the optional data flash memory. The memory controller capabilities vary between the two 
banks with each bank’s functionality optimized with the typical use cases associated with the attached 
flash memory. As an example, the platform flash memory controller logic associated with the code flash 
memory bank contains a four-entry page buffer, each entry containing 128 bits of data (1 flash memory 
page) plus an associated controller that prefetches sequential lines of data from the flash memory array 
into the buffer, while the controller logic associated with the data flash memory bank only supports a 
128-bit register that serves as a temporary page holding register and does not support any prefetching. 
Prefetch buffer hits from the code flash memory bank support zero-wait AHB data phase responses. AHB 
read requests that miss the buffers generate the needed flash memory array access and are forwarded to the 
AHB upon completion, typically incurring two wait-states at an operating frequency of 60–64 MHz.

This memory controller is optimized for applications where a cacheless processor core, e.g., the Power 
e200z0h, is connected through the platform to on-chip memories, e.g., flash memory and SRAM, where 
the processor and platform operate at the same frequency. For these applications, the 2-stage pipeline 
AMBA-AHB system bus is effectively mapped directly into stages of the processor’s pipeline and zero 
wait-state responses for most memory accesses are critical for providing the required level of system 
performance. 

30.7.1.2

Features

The following list summarizes the key features of the platform flash memory controller:

•

Dual array interfaces support up to a total of 16 MB of flash memory, partitioned as two separate 
8 MB banks

Содержание MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды