NuAire LabGard NU-581-400E Скачать руководство пользователя | Manualshive

Страница: 52 / 108

background image

OM0303
Rev 5 July/2021

Page 52 of 108

7.3 Secondary HEPA Filter/Motor Replacement

The HEPA Filters under normal usage and barring an accident (a puncture), do not need replacement until the efflux
velocity cannot be maintained or the access inflow velocity cannot be maintained at 100 LFPM (.51 m/s) (min.). This may
permit the average downflow velocity to be as low as 55 LFPM (.27 m/s) as long as no point falls below 20% of the average
downflow velocity.

The HEPA Filters should not be replaced until the entire cabinet has been decontaminated or known to be biologically
"clean".

7.3.1

Procedure

Disconnect electrical power from the cabinet before attempting any

maintenance action.

Step 1:

Remove screws at each upper side of the control center and allow the control center to rotate down,

resting on the safety straps. Second, remove the front decorative panel which is held into position by

(3) knurled nuts on the top edge and snap fit bullet catches on the bottom.

Step 2:

Place sliding window into lowest position * and remove front filter panel, which is held into position by

Phillip pan head screws. Once the screws are removed, the panel is held into position by smooth weld

studs located on the top corner of the front filter panel. Use the window stop brackets as handles to

remove the panel.

NOTE: Screws are used in lieu of acorn nuts, and lock washers.

The screws have O-rings and should be replaced if damaged or badly deformed.

The interior of the cabinet is now fully exposed for replacement of the filters and/or motor/blower.

*The lowest window position will require the armrest to be removed. If the cabinet has the power window option,
access the Power Window Test menu to adjust the power window into its lowest position with the armrest
removed. Access Calibration/Service menu, then Service menu, then Power Window menu to Power Window
Test.

Step 3: Filter Removal

It is not always necessary to replace both the supply and exhaust filters at the same time. If during the
course of certifications, the downflow always falls off while the exhaust increases the supply filter is
"loading" faster than the exhaust filter and only the supply filter may need replacement. The opposite
might also happen depending upon many factors.

a. To remove the supply filter:

1. Remove the plenum screws in front of the supply HEPA filter.

2. Lift the permanent plenum and hold up with wire strap.

3. Carefully remove the supply filter. Direct exposure should be avoided.

Dispose of spent HEPA filters properly.

Avoid direct contact to "dirty side" of the filters.

Place in sealed bag and label all waste containers/cartons based on

type of hazard. Follow all Local, State and Federal guidelines for

disposal of HEPA filter solid waste.



CAUTION

!

CAUTION

!

«
...
50
51
52
53
54
...
»

Содержание LabGard NU-581-400E













































































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard NU-581-400E

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: FENDT Страницы: 31

Бренд: GE Страницы: 698

Бренд: Tate Страницы: 7

Бренд: Tate Страницы: 5

BioHarmonex BH4

Бренд: Calivita Страницы: 38

Бренд: CAIRE Страницы: 91

Бренд: ACCU-CHECK Страницы: 104

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Бренд: ValueStore US Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды