NuAire LabGard NU-581-400E Скачать руководство пользователя | Manualshive

Страница: 5 / 108

background image

OM0303
Rev 5 July/2021

Page 5 of 108

LabGard® ES HD Energy Saver

Class II, Type A2 Laminar Flow

Biosafety Cabinet

Models

NU-581-400E/500E/600E

Manufactured by:

Nuaire, Inc. - Plymouth, Minnesota, U.S.A.

1.0

General Information

1.1 Description

The LabGard® ES HD Model NU-581E Laminar Flow Biosafety Cabinet (LFBSC) is a bench/table top model, optionally
available with a base support stand, for operation as a console model. The LabGard® ES model NU-581E utilizes an Energy
Saver DC ECM motor optimally determined forward curved fan for each model size/width to maximize both energy
efficiency and filter loading capacity. The Energy Saver ECM motor is controlled airflow setpoints via a solid-state DC motor
controller with digital dual thermistor airflow sensors that provide an automatic compensation (constant volume control)
for both filter loading and line voltage variances.

The Laminar Flow Biosafety Cabinet, (LFBSC) is a product resulting from the development of the "laminar flow" principle
(see Airflow Schematic) and the application of environmental controls as required in the field of biological research or
(Hazardous Drug) chemical containment. The LFBSC, when used with proper technique, is an effective primary engineering
control in obtaining the optimum product quality while reducing the potential for exposure of both product and personnel
to airborne biological or particulate chemical agents in low to moderate risk-hazard research and drug preparation or
product operations, as prescribed by the Center for Disease Control (CDC) Atlanta, Georgia.

The NU-581E bench LFBSC meets the requirements of a Class II, since the cabinet conforms to the following requirements:

1.  Maintains a minimum inflow velocity of 100 LFPM (.51mps) through the work access opening.

2.  Has HEPA filtered downflow air that is mixed with the inflow air from a common exhaust plenum.

3.  Discharges a percentage of air to the outside atmosphere after HEPA filtration.

4.  Has all biologically contaminated ducts and plenums under negative pressure or surrounded by negative pressure.

If working with volatile chemicals, the cabinet must be connected to an external exhaust system with a canopy transition.
Type A2 cabinets may be used for work with volatile chemicals if permitted by a chemical risk assessment.

«
...
3
4
5
6
7
...
»

Содержание LabGard NU-581-400E













































































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard NU-581-400E

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Hanil Страницы: 60

Бренд: Jacobs Ladder Страницы: 16

Бренд: ACCU-CHECK Страницы: 104

Бренд: DBX Bushido Страницы: 12

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: Hacker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды