NuAire LabGard NU-581-400E Скачать руководство пользователя | Manualshive

Страница: 41 / 108

background image

OM0303
Rev 5 July/2021

Page 41 of 108

Perform decontamination procedure per NSF/ANSI 49, Annex I-2 (formerly Annex G).

If the cabinet has been used to prepare antineoplastic drugs, (chemotherapy), or other toxic chemicals,
decontamination of the cabinet

cannot

be accomplished by the above procedure. It is recommended that the

following protective measures be taken:

1.

Gloves

Gloves must be worn.  Care must be taken not to cut, puncture, or tear the gloves.  No one glove material
is impervious to all CYTAs; disposable surgical or polyvinyl chloride (PVC) gloves provide substantial but
not complete protection.  PVC gloves probably are more protective than surgical gloves, but they are
stiffer and less tactile.  Gloves should be discarded after each use.  Gloves should be tucked into the cuffs
of the gown.  Double gloving should be considered.

2.

Face & Eye Protection

A disposable dust and mist respirator and either a plastic face shield (preferred) or chemical splash
goggles must be worn. The face shield or goggles should be wiped clean with a suitable tissue and water
after each use.

3.

Gowns

A protective garment must be worn.  The garment should be made of lint-free, low-permeability fabric
and must have a closed front, long sleeves, and elastic or knit closed cuffs.  Tyvek¹ isolation gowns are one
example of an acceptable garment.  The garment must be worn outside the work area.  Disposable gowns
are preferred over reusable.  Front-buttoned coats are not recommended.

4.

Hair & Shoe Covers

Disposable hair and shoe covers should be worn.

5.

Motion

Slow and deliberate motions are necessary when working in the interior of the cabinet, in order to
minimize the generation of particulates.

Please consult with Nuaire, Inc. about any unique contamination problems.

Normally, no preventive maintenance is required on the interior of the cabinet (i.e., the area behind the access
panel containing the HEPA filters and motor (blower assembly). All required adjustments in order to maintain
proper cabinet airflows are external to the cabinet interior. The motor is lubricated for life and is thermally
protected with automatic reset.

¹ Available from Lab Safety Supply, Janesville, WI 53547-1368, or other laboratory, industrial, or hospital supply distributor

«
...
39
40
41
42
43
...
»

Содержание LabGard NU-581-400E













































































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard NU-581-400E

Бренд: Olympus Страницы: 86

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: GALLERY Страницы: 18

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: York Fitness Страницы: 34

Бренд: Hanil Страницы: 60

Бренд: BACtrack Страницы: 16

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: jcb Страницы: 41

Бренд: Garmin Страницы: 20

Бренд: Madsen Страницы: 206

Бренд: Yetter Страницы: 24

Бренд: Accurate Technology Страницы: 10

Бренд: Gage Bilt Страницы: 28

Бренд: Dantel Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды