NuAire LabGard NU-581-400E Скачать руководство пользователя | Manualshive

Страница: 37 / 108

background image

OM0303
Rev 5 July/2021

Page 37 of 108

6.6 Hazardous Drug Decontamination Procedures

This procedure is intended to provide guidance following a spillage and/or periodic maintenance, testing or relocation of
the cabinet. Additional guidance can be provided by the CETA document CAG-005-2007 found at the CETA website:
www.CETAinternational.org.

6.6.1

Preparation

Prior to beginning decontamination activity, personnel should wear proper personnel protection equipment (PPE)

i.e. Tyvek

1

isolation gown, 2 pair of Nitrile gloves and a full-faced HEPA filtered respirator. All protective garments

should be contained in 4 mil plastic bags and labeled for disposal as chemotherapy waste after completion of the
procedure. For the purpose of this procedure, detailed procedures for cleaning a Class II BSC can be found in the
2006 ASHP Technical Assistance Bulletin

ASHP Guidelines on Handling Hazardous Drugs

2

.

6.6.2

Procedure

a. Make sure that the cabinet remains in operational mode with internal blower on.
b. Open the hinged or sliding view screen and secure in the full open position.

With the view screen in the full open position, personnel protection

is compromised and a full faced HEPA filtered respirator must be

worn.

c. Clean all readily accessible surfaces of the cabinet.
d. Remove perforated metal diffuser screen from the underside of the supply HEPA filter and place on the

cabinet work tray.

NOTE:

Depending on the model, the diffuser screen is secured to the cabinet by #8-32 screws or

1/4" - 20 acorn nuts, 3 places. It is purposely a tight fit and is secured to the back wall with

projecting threadless studs.

e. Clean both sides of the perforated metal diffuser screen and remove it from the cabinet.
f.

Lift the cabinetwork tray, clean both sides and remove it from the cabinet.

g. Remove the front perforated grill, place on the cabinet floor and clean both sides.

Remove from cabinet.

h. Clean work tray supports.

i.

Working from top to bottom, clean all inside surfaces of the cabinet. Take care

not

to wet the HEPA filter.

If liquid has collected in the plenum drain, aspirate it using IV tubing into an evacuated container. Label

the evacuated container for disposal as chemotherapy waste.

j.

Clean the plenums drain area and wipe dry.

k. If the cabinet requires maintenance and/or replacement of the HEPA filters, the operation should be

halted at this point to allow trained personnel to complete replacement of the HEPA and/or maintenance
action required.

6.6.3

Assembly

a. Replace front (if removed) grill.

b. Replace the work tray and carefully tighten the thumbscrews.

c. Replace perforated metal diffuser screen over the underside of the supply HEPA filter.

d. Wipe down all exposed surfaces of the work area with 70% isopropyl alcohol.

e. Prepare for aseptic operation.



CAUTION

!

«
...
35
36
37
38
39
...
»

Содержание LabGard NU-581-400E













































































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard NU-581-400E

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: 3M Страницы: 2

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: Tar River Страницы: 61

Бренд: NAMYSLO Страницы: 13

Бренд: Floe Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды