NuAire LabGard NU-581-400E Скачать руководство пользователя | Manualshive

Страница: 21 / 108

background image

OM0303
Rev 5 July/2021

Page 21 of 108

6.1.4

Night Setback/ Nite Care Mode

The NU-581E may be optionally configured to allow the DC ECM motor to continue to run at a lower rate with the
sliding window closed allowing the workzone interior to be continually HEPA filtered.  If the night setback mode is
configured, the blower icon must be on and the window closed for it to be activated.  In addition, the LED light will
be disabled.  If the sliding window is then opened the cabinet will resume normal airflow setpoints in run mode.

6.1.5

Standby/Run Mode Alarms

If present standby/run mode alarms will be both visual and audible, the Red LED oval under the LCD display will
turn on, and the

TOUCHLINK

LCD screen will also display a description of the alarm. Audible alarms can be silenced

or will produce an alarm tone for 10 seconds, then into a ring back cycle of once every 2 seconds. Pressing the
alarm silence icon will silence the audible alarm for 15 minutes then into a ring back cycle of once every 2 seconds

Alarm Types

The middle of the display just below the icons is the message area that will indicate alarms, errors or other notable
conditions. Since the message area is limited to one line of text, only the highest priority message will be
indicated. However, for alarm conditions, also displayed is a caution symbol and pressing it will display all present
alarm conditions. The list below represents the highest to lowest priority.

•

Runtime Failure

•

Power Loss Alert

•

Downflow Sensor Error

•

Inflow Sensor Error

•

Exhaust Sensor Error

•

Downflow Sensor Communication

•

Inflow Sensor Communication

•

Exhaust Sensor Communication

•

Downflow Low Limit

•

Downflow High Limit

•

Inflow Low Limit

•

Inflow High Limit

•

Exhaust Low Limit

•

Exhaust High Limit

•

Cabinet Pressure Low

•

Window High

•

Window Low

•

Replace Filter

•

Replace UV Lamp

•

Recertification Past Due

•

Recertification Due In (x) Week(s)

«
...
19
20
21
22
23
...
»

Содержание LabGard NU-581-400E













































































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard NU-581-400E

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Bacharach Страницы: 48

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: Faderfox Страницы: 8

Tablet1000 Series

Бренд: Hantek Страницы: 98

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды