NuAire LabGard NU-581-400E Скачать руководство пользователя | Manualshive

Страница: 49 / 108

background image

OM0303
Rev 5 July/2021

Page 49 of 108

7.2 LED Lamp Replacement

The two (T8) LED lamps are cool white and placed external to the cabinet to aid maintenance and minimize heat build-up
within the cabinet. The B70 life rating of the lamp is 50,000 hours based on 80,000 switching cycles.

To replace a lamp, it is necessary to remove the lamp assembly.

1. Switch Cabinet Light Switch off.

2. Remove the screws at each upper side of the Control Center and allow the Control Center to rotate down, resting

on the safety straps.

3. The lamp is now directly exposed for replacement.

4. The lamp is removed by displacing the lamp to one side against the compressible lamp holder and lifting out the

lamp.

5. Reverse the procedure to reinstall the lamp assembly being careful not to pinch the safety straps, cable or tubing

during closure of the control center.

7.3 Primary HEPA Filter Prefilter Replacement

The primary HEPA prefilters under normal usage and barring an accident (a puncture), do not need replacement until the

efflux velocity cannot be maintained or the access inflow velocity cannot be maintained at 100 LFPM (.51 m/s) (min.). This
may permit the average downflow velocity to be as low as 55 LFPM (.27 m/s), as long as no point falls below 20% of the
average downflow velocity.

If the above airflow requirements cannot be maintained use the following procedure to replace the primary HEPA

prefilters.

Sliding window should never be opened unless interior is known to be free of

hazardous drug residue or appropriate precautions are taken per facility Standard

Operating Procedures (SOP’S).

NOTE

: Cabinet should be on and running throughout the filter replacement process.

1. Using appropriate PPE, surface decontaminate or clean cabinet workzone interior including both sides of the

worktray.

2.  Remove worktray from cabinet and be sure window is at nominal work height.
3.  Remove protective screen from primary HEPA prefilter that is going to be replaced and set aside within workzone.
4.  Bend and collapse the protective screen then discard the protective screen by inserting it into the used filter that is

to be replaced.

CAUTION

!



«
...
47
48
49
50
51
...
»

Содержание LabGard NU-581-400E













































































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard NU-581-400E

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: TAIKO Audio Страницы: 24

Бренд: Cambro Страницы: 6

Бренд: Hammer Страницы: 42

Бренд: Taylor Страницы: 60

Бренд: TANDBERG Страницы: 23

Бренд: Oakworks Medical Страницы: 28

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Samson Страницы: 2

Бренд: T&D Страницы: 28

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды